Summer is in full swing here in Southern California! We knew heading into Summer this year that we wanted to make the most of our outdoor space, and that all started with a hot tub. Then of course, me being me, I had to DECORATE the hot tub area. 😛 (I mean, duh. Right?!)
So, add on a pergola, rugs, pillows, plants, and the best part – an outdoor bar area with bar stool seating. Not only can we now eat a nice dinner out here (because yes, every pergola also needs a vintage chandelier hanging from the middle), but the bar is the same height as the hot tub itself, which gives us a safe place to set our wine, beer, water, etc, when we are taking a dip.
**This post may contain affiliate links – read our full Disclosure here**
And that’s it! So easy and inexpensive!
After your wood is cut to the length you need, use your electric sander to sand the wood until it is fairly smooth to the touch.
Decide which side of your wood will be the top, and flip it over so that the bottom of the wood is facing up.
Align your hairpin legs to the very edge of each corner. We weren’t super precise about this, we just lined them up to sight and touch.
Now take your drill and screws and screw each leg into place.
Now that your legs are attached, flip your table to stand.
Time to wax!
PRO TIP: If you PAINT your bar, you’ll want to do so BEFORE you attach the legs. You could also wax your wood BEFORE you screw the legs on, but I didn’t have an issue doing it after the fact. I personally wasn’t sure how I was going to finish the table top, and I wanted the bar to actually use ASAP. It worked out that I ended up waxing and not painting!
Use your first rag to apply the wax liberally to your wood, in the same direction as the grain. Make sure you get the top, sides, and bottom. Be careful with how much wax you get on your rag though, as the wax tends to fly off and land on the floor (or you!) when you least expect it! You could always put down a plastic tarp to save the floor surface, or tackle this step in the grass where it wont matter! Also make sure you’re wearing clothes you don’t care about!
Once your bar top is completely waxed, allow to sit for about 20 minutes. Now take a clean rag and buff the entire thing – really put some elbow grease into this, as this is what makes the waxed wood super smooth to the touch.
PRO TIP: DO NOT apply Polycrylic on top of your wax. Yup, I totally did – no bueno. (This is what happens when you DO first and RESEARCH later. Lesson learned on that one!) I applied the Poly because I wanted to ensure maximum waterproofing, but water based over oil based is a no go. So, we had to sand ours back down and re-wax. No big deal really, just annoying. (And honestly, the wax itself is really a very decent water barrier, and you can always apply another coat of wax to increase the waterproofing and/or increase the richness of the color).
However, if you PAINT your bar top, you’ll definitely want to seal it with Polycrylic or Water based Polyurethane of some sort. Even if your bar is not next to a hot tub, I can assure you it will still get wet!
Allow to dry for 24 hours before use. Now enjoy, and relax!
It’s that easy friends! And such a great inexpensive alternative to all of the outrageously priced outdoor bars that are actually on the market (seriously, the ones I liked were between $300 and $500, where as this cost under $100)! And the best part is you can customize it to your exact specifications!
Soon I’ll do a blog about all the other details of this space, because the before and after is really quite mind blowing (we used to have a metal shed on this concrete slab and a bunch of giant banana palms/black birds of paradise in that flower bed)!
But until then, I hope this tutorial gave you a fun new idea for transforming your outdoor space into a fun place to gather with family and friends. Until next time…
October 2018 Update:
It seems with the general wear and tear and moisture changes that naturally happen from being outside, that I will likely have to do a quick sand and re-wax seasonally. The wood, due to moisture levels, has seeped sap, which I need to get off. Now, my guess is I could use an outdoor oil based varnish of some kind to really seal it, which I might do. But for now, having to spend an hour or so every 5-6 months to clean the bar up isn’t a big deal! Just know if you want it SUPER outdoor proof, you’ll have to add a topcoat to your finished product!
I know it's been a while since I've posted here, let alone about our dream…